MASK Control Systems - Bespoke Industrial Automation & Control Systems UK
High-Voltage 800V ArchitectureGigafactory & Tier 1 Automation16 min read

EV Battery Pack & Module Assembly Automation: Laser Welding, Dielectric Testing & Clean-Dry Room Controls

Turnkey automation architectures for electric vehicle battery module and pack assembly. MASK designs and commissions robotic cell grading, laser busbar welding synchronization, closed-loop 2K thermal interface material (TIM) dispensing, 5kV dielectric Hipot testing stations, and Class 1 Div 2 dry room control panels.

Robotic EV battery pack assembly cell with laser welding and automated inspection
Module & Pack Assembly Automation
Laser Busbar Joining | 5kV Dielectric Hipot | 100% Digital Passport
VOLTAGE RANGE
400V / 800V DC
Cat 4 PLe HVIL Interlocks
WELD INTEGRITY
< 10 µΩ
4-Wire Kelvin Busbar Check
TIM DISPENSING
±1.0% Ratio
Closed-Loop 3D Profilometry
DRY ROOM RATING
-50 °C Td
ATEX Zone 2 / DSEAR Purge
STANDARDS & DIRECTIVES:
ISO 6469-3 (Electric Vehicle Electrical Safety)UN 38.3 (Transport Testing)IATF 16949 / EU Battery PassportBS EN ISO 13849-1 (Cat 4 PLe)DSEAR / ATEX Zone 2 (Electrolyte Off-Gas)UL 2580 / ECE R100 Rev 2
Battery Manufacturing Challenges

High Voltage, Thermal Runaway & Precision Micro-Joining Bottlenecks

As the UK and Europe accelerate gigafactory capacity and commercial vehicle electrification, battery pack assembly lines face unmatched engineering hurdles. Combining volatile electrochemical energy with 800V DC potentials requires zero-defect assembly automation. A single defective busbar weld or void in the thermal interface paste can trigger irreversible thermal runaway or pack failure.

High-Voltage Shock & Arc Flash

As modules are mechanically wired in series, open live circuits quickly exceed 400V to 800V DC. Uncontrolled contact or insulation breakdown presents lethal electrical shock and severe arc flash hazards, requiring automated robotic isolation and interlocked test enclosures.

Thermal Runaway & Gas Ejection

Punctured pouch cells, internal micro-shorts during compression, or localized laser overheating can initiate cell venting and toxic HF gas release. Assembly cells must integrate rapid off-gas sensors, emergency extraction dump gates, and inert fire suppression.

Strict Digital Battery Passport Rules

The European Union Battery Regulation and OEM PPAP requirements mandate 100% cradle-to-grave genealogy. Every individual cell serial number, laser weld energy signature, Hipot dielectric leakage curve, and BMS calibration profile must be permanently recorded and searchable.

Manual / Semi-Automated Bench Setup vs MASK Automated EV Pack Line Architecture

How our integrated industrial automation overcomes quality risks, tact-time limits, and safety liabilities.

Process StageManual / Semiautomatic ProductionMASK Automated EV Assembly Architecture
Cell Grading & SortingManual probe application; batch averages written on paper sheets. High human error.Automated robotic OCV/AC-IR Kelvin station (±0.1mV / ±0.01mΩ) with instant 2D DataMatrix barcode binding.
Busbar JoiningManual TIG welding or ultrasonic hand fixtures. Inconsistent spatter and tab heat damage.Galvo-scanner fiber laser welding with wobble path control, real-time pyrometer keyhole depth feedback.
TIM DispensingManual cartridge caulking gun. Uneven bead thickness and critical trapped air pockets.Closed-loop 2K volumetric gear pumps, automated servo robotic rastering, and 3D laser profilometry inspection.
High-Voltage Hipot SafetyManual test leads applied by technicians. Lethal 800V shock risk during isolation faults.Automated pneumatic bed-of-nails docking chamber with Cat 4 PLe HVIL interlocks, automated discharge relays.
Cooling Jacket Leak CheckWater bubble tank or simple air pressure drop. Misses micro-leaks below 1 mbar.Automated helium mass spectrometer chamber testing down to 1x10^-5 mbar·l/s before pack closing.
Genealogy & TraceabilityDisjointed spreadsheets or paper travelers. Inadequate for OEM IATF 16949 audits.Full digital battery passport generation via OPC UA / SQL: 100% weld curves, test values, and component batch IDs.
Engineering Discipline

Five Engineering Pillars of EV Battery Pack & Module Automation

From incoming prismatic cell testing to final 800V DC end-of-line verification, our control architectures ensure cycle time efficiency, millivolt-level accuracy, and complete operator protection:

01

Automated Cell Grading, Polarity Vision & Precision Servo Stacking

Prior to stacking, cells must be graded to ensure matched internal impedance and uniform capacity degradation across the vehicle lifetime. Our automated cells utilize high-speed pneumatic Kelvin probes to measure Open Circuit Voltage (OCV) to ±0.1 mV and AC Internal Resistance (AC-IR at 1 kHz) to ±0.01 mΩ. Machine vision verifies terminal polarity before robotic pick-and-place systems stack cells with aerogel/mica thermal barriers, applying closed-loop servo compression to target kilonewtons prior to PET or steel side-banding.

OCV (±0.1 mV) & AC-IR (±0.01 mΩ) 4-Wire Testing
Machine Vision 2D Barcode & Polarity Validation
Closed-Loop Servo Stacking Compression (±50 N)
Automated Thermal Insulation / Aerogel Placement
CELL SORTING SPECS
OCV Precision±0.1 mV Digital
AC-IR Frequency1 kHz Standard
Cycle Time< 2.5s per Cell
Cell FormatsPrismatic, Pouch, 4680
02

Laser Busbar Welding Control & Real-Time Keyhole Pyrometry

Joining high-conductivity copper busbars to aluminium cell terminals requires exceptional energy control to prevent brittle intermetallic compound formation. MASK synchronizes multi-axis robot motion with 4kW to 6kW single-mode fiber lasers and galvanometer scanning heads. We execute high-frequency wobble patterns while coaxial optical pyrometers sample keyhole light emissions at 100 kHz, instantly flagging voids, spatter, or incomplete penetration.

Galvanometer Scanner & Robot Motion Synchronisation
High-Frequency Wobble Geometry (Cu-to-Al Joining)
Coaxial 100 kHz Photodiode / Pyrometer Weld Quality
Fume Extraction & Laser Class 1 Interlocked Cells
LASER PROCESS STATS
Laser Source4kW to 6kW Fiber
Sampling Rate100 kHz Pyrometry
Post-Weld Triangulation3D Laser Bead Scan
Joint Resistance< 10 µΩ (Micro-Ohm)
03

Closed-Loop 2K Thermal Interface Material (TIM) Dispensing

Efficient heat rejection to the liquid cold plate depends entirely on void-free thermal interface material. MASK integrates closed-loop servo-driven dual-component (2K) volumetric metering systems. As the robot applies thermal paste in programmed raster patterns, coaxial or trailing 3D laser profilometers verify bead width, height, and continuity in real time, preventing trapped air pockets that cause localized thermal hot spots.

Volumetric Gear Metering with Dynamic Ratio Control
Automatic Viscosity & Temperature Conditioning
Real-Time 3D Laser Bead Profilometry & Gap Inspection
Automated Nozzle Purging & Needle Tip Calibration
DISPENSING CONTROLS
Mix Ratio Tolerance±1.0% Stoichiometric
Bead Height Accuracy±0.1 mm Optical
Viscosity RangeUp to 2,000,000 mPa·s
Air Pocket Detection100% Automated
04

5kV Dielectric Hipot, Insulation Resistance & Low-Resistance Verification

Prior to pack sealing, safety-critical electrical testing verifies dielectric isolation between high-voltage busbars and the grounded aluminium tray/cooling plate. Our automated test stations apply up to 5 kV DC dielectric withstand (Hipot) testing, measuring leakage currents down to microampere thresholds. We verify insulation resistance (>100 MΩ at 1,000V DC) and ground bond continuity (<100 mΩ at 25A) in a fully interlocked safety enclosure.

5 kV DC Dielectric Withstand (Hipot) Test Enclosures
Insulation Resistance (> 100 MΩ at 1,000V) Testing
4-Wire Kelvin Busbar Micro-Ohm Resistance Checks
Automatic Capacitive Discharge Relays Before De-latch
ELECTRICAL SAFETY TEST
Hipot VoltageUp to 5,000 V DC
Leakage Threshold< 1 mA Limit
Ground Continuity< 100 mΩ @ 25 A
Safety InterlockCat 4 PLe Trapped Key
05

BMS Programming, Helium Leak Testing & Dry Room Control Systems

Final pack closure requires end-of-line (EOL) functional verification. We engineer bed-of-nails pogo-pin docking stations for automated Battery Management System (BMS) firmware flashing over CAN FD / Automotive Ethernet, validating contactor sequencing, pre-charge circuit timing, and cell balancing telemetry. Simultaneously, automated helium mass spectrometers verify cooling circuit hermeticity, while custom stainless ATEX Zone 2 panels regulate dry room HVAC and emergency Novec 1230 fire suppression.

BMS Flashing & Communication Validation (CAN FD / LIN)
Helium Mass Spectrometer Cold Plate Leak Testing
-50 °C Dew Point Dry Room & ATEX Zone 2 Panel Builds
Digital Battery Passport Cloud / MES Archiving
EOL TESTING STATS
CommunicationCAN FD / Automotive Eth
Leak Rate Sensitivity1x10^-5 mbar·l/s
Fire SuppressionNovec 1230 Interlocked
Genealogy ExportSQL / JSON Battery Passport
Cell Geometry Engineering

Prismatic vs Pouch vs Cylindrical (4680) Assembly Configurations

Automation requirements vary substantially depending on the selected cell form factor. MASK engineers tooling and software architectures tailored to all three core EV formats:

Process ParameterPrismatic Hard-Case CellsPouch Cells (Laminate)Cylindrical 4680 / 21700 Cells
Cell Stacking & CompressionRobotic pick-and-place with servo-driven end-plate clamping (2 kN to 6 kN force)Delicate vacuum gripper transfer into plastic cassette frames with foam spacersHigh-speed continuous rotary honeycomb matrix pocket insertion
Terminal AlignmentRigid top terminal posts; machine vision offsets for laser scanner focusFlexible foil tabs; requires automated mechanical clamping before ultrasonic/laser weldDirect tabless end-cap laser welding or wire bonding to current collectors
Thermal Interface DispensingBottom plate 2K gap filler dispensing; high thermal conductivity (2 to 3 W/m·K)Intercalated cooling fin thermal paste or side-mounted cold plate channelsIntrusion potting / polyurethane structural foam injection around cell bodies
Critical Quality RiskTerminal weld penetration damaging internal jelly roll seals; case deformationFoil tab tearing, pouch seal delamination, and puncture during compressionUneven current distribution across hundreds of parallel connections
Standard MASK ArchitectureRockwell GuardLogix + Trumpf 4kW Fiber Laser + Beckhoff EtherCAT measurementSiemens S7-1500F + Fanuc SCARA/6-Axis + Schunk vacuum handlingSiemens Simatic F-CPU + Festo high-speed pneumatic matrix + Cognex vision
Tier 1 Industrial Hardware

Built Upon Trusted Automotive & Battery Automation Systems

We engineer control systems complying with BS EN 60204-1 and ISO 13849-1, deployed on the hardware platforms specified by leading European battery gigafactories and automotive OEMs:

AUTOMOTIVE OEM

Rockwell Allen-Bradley GuardLogix

GuardLogix 5580 safety controllers, Point Guard I/O, Kinetix 5700 multi-axis servo drives, and CIP Safety over EtherNet/IP for robotic assembly and dispensing coordination.

Explore Allen-Bradley Services
EUROPEAN GIGAFACTORY

Siemens S7-1500F & TIA Portal

SIMATIC S7-1500F fail-safe CPUs with ET 200SP Safety, Sinamics S120 drives, PROFIsafe, and integrated WinCC Unified HMIs with encrypted recipe management.

Explore Siemens Services
ULTRA-FAST LASER & I/O

Beckhoff TwinCAT 3 & EtherCAT

PC-based industrial controllers with sub-millisecond EtherCAT cycle times for direct galvanometric laser scanner sync, pyrometer sampling, and high-speed vision.

Systems Integration Services
Turnkey Project Delivery

Our 5-Stage Battery Line Design & Commissioning Workflow

Bringing an EV pack assembly line from CAD concept to validated production requires stringent stage-gate rigor:

01

Process FMEA & Safety Audit

Design review of high-voltage hazard zones, thermal runaway venting scenarios, ISO 6469-3 electrical safety requirements, and dry room environmental loads.

02

EPLAN Schematics & Build

Bespoke panel design to BS EN 60204-1, Class 1 Div 2 / ATEX Zone 2 purge enclosures, segregated high-voltage bus ducts, and in-house FAT staging.

03

PLC, Robot & Laser Code

Fail-safe PLC programming (Cat 4 PLe), multi-axis robot motion paths, galvo scanner wobble routines, and closed-loop TIM dispensing algorithms.

04

Dry Room Installation

Clean-dry room mechanical and electrical rigging, laser class enclosure light curtain integration, helium chamber installation, and field bus commissioning.

05

PPAP & Battery Passport Sign-Off

Gauge R&R validation on OCV/AC-IR and Hipot stations, destructive weld peel testing correlation, MES digital passport integration, and CE/UKCA marking.

Engineering Guidance

EV Battery Pack Automation Questions Answered

Expert answers on laser welding parameters, high-voltage Hipot safety interlocks, and dry room panel standards.

How do MASK control systems handle high-voltage electrical safety during module assembly?
During module stacking and busbar attachment, voltages accumulate rapidly up to 800V DC. We engineer safety circuits to BS EN ISO 13849-1 Cat 4 PLe with dual monitored High-Voltage Interlock Loops (HVIL), isolated ceramic test beds, automatic grounding discharge relays, Class 0/00 insulated end-effectors on transfer robots, and optical light curtains interlocked with high-voltage test gates.
What sensing methods verify busbar weld integrity on copper-to-aluminium joints?
Welding dissimilar metals (copper busbars to aluminium cell terminals) requires sub-millisecond process feedback. We integrate real-time optical pyrometers and coaxially mounted camera sensors measuring keyhole emission spectra, followed by automated 3D laser line triangulation for weld bead geometry and 4-wire Kelvin micro-ohmmeter contact resistance checks under 10 micro-ohms.
How is thermal interface material (TIM) dispensing controlled and inspected?
We control dual-component (2K) volumetric gear metering pumps via closed-loop servo drives, maintaining an exact stoichiometric mix ratio and temperature. As the robotic dispensing head travels, high-speed 3D laser profilometers inspect bead height, width, volume, and continuity to eliminate air bubbles that could create hot spots between battery cells and the liquid cold plate.
What environmental controls are required for dry room battery automation panels?
Dry rooms operate at extremely low dew points (-40 deg C to -50 deg C), which can degrade conventional electrical insulation and dry out pneumatic seals. We build sealed stainless-steel control enclosures with specialized dry-air purge systems, desiccated air seals, ATEX/DSEAR Zone 2 rated components for volatile electrolyte exposure, and inert gas fire suppression interlocks.
How is individual cell and module genealogy tracked for battery passport compliance?
Every incoming cell is scanned via 2D DataMatrix barcode during OCV/AC-IR grading. The automation platform binds cell serial numbers, open circuit voltage, internal resistance, laser weld parameters, Hipot dielectric leakage, and TIM bead profiles into a structured JSON/SQL record, delivering complete digital battery passport traceability compliant with EU regulations and IATF 16949.
Can MASK integrate automated helium leak testing for battery pack liquid cooling jackets?
Yes. We engineer automated vacuum chamber and sniffer test interfaces using helium mass spectrometry. The cooling jacket is evacuated, charged with helium tracer gas, and monitored down to 1x10^-5 mbar litres per second to guarantee that ethylene-glycol coolant can never escape into high-voltage electrical compartments.
Speak Directly With Mike

Scale Your EV Battery Pack Assembly with Turnkey Automation

Whether you need automated laser busbar welding, 5kV Hipot electrical safety test enclosures, closed-loop 2K TIM dispensing, or dry room control panels, MASK delivers validated industrial automation engineered to automotive OEM and gigafactory standards.

Direct engineering consultation
High-voltage 800V Cat 4 PLe safety
Digital battery passport traceability
WhatsApp